ASTM A403 A403M Standard Specification for Wrought Austenitic Stainless Steel Piping Fittings

pipe fittings materials data

you may also check non standard sizes pipe fitting weight online calculation, pipe fitting surface area online calculation,pipe fitting surface volume online calculation from our pipeline tool link:

https://alloypipefitting.com/fitting-calculator.html

For the pipe fitting material, please check butt-weld-fitting-standard-data

Abstract

This specification covers the standard for wrought austenitic stainless steel fittings for pressure piping applications. The material for fittings shall consist of forgings, bars, plates, or seamless or welded tubular products. Forging or shaping operations shall be performed by hammering, pressing, piercing, extruding, upsetting, rolling, bending, fusion welding, machining, or by a combination of two or more of these operations. All fittings shall undergo heat-treatment. Chemical and product analyses shall be performed and shall conform to the required chemical composition in carbon, manganese, phosphorus, sulfur, silicon, chromium, molybdenum, and titanium. Tension test shall be done on the fitting material to determine the tensile properties such as yield strength and tensile strength. Fittings supplied under this specification shall be examined visually for surface discontinuities, surface checks, and mechanical marks.

Scope

1.1 This specification covers wrought stainless steel fittings for pressure piping applications.2

1.2 Several grades of austenitic stainless steel alloys are included in this specification Grades are designated with a prefix, WP or CR, based on the applicable ASME or MSS dimensional and rating standards, respectively.

1.3 For each of the WP stainless grades, several classes of fittings are covered, to indicate whether seamless or welded construction was utilized. Class designations are also utilized to indicate the nondestructive test method and extent of nondestructive examination (NDE). Table 1 is a general summary of the fitting classes applicable to all WP grades of stainless steel covered by this specification. There are no classes for the CR grades. Specific requirements are covered elsewhere.

TABLE 1 Fitting Classes for WP Grades

 Class

  Construction

 Nondestructive Examination

 S

  Seamless

 None

 W

  Welded

 Radiography or Ultrasonic

 WX

  Welded

 Radiography

 WU

  Welded

 Ultrasonic

1.4 This specification is expressed in both inch-pound units and in SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished to inch-pound units.

1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.6 This specification does not apply to cast steel fittings. Austenitic stainless steel castings are covered in Specifications A351/A351MA743/A743M, and A744/A744M.

C&N Huitong group can produce pipe fittings of such materials :

ASTM Standard MaterialASTM A53 A53M Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless
ASTM A106 A106M Standard Specification for Seamless Carbon Steel Pipe for High-Temperature Service
API 5L Specification for Line Pipe
ASTM A213 2018 Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes
ASTM A312 A312M Standard Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes
ASTM A234 A234M Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Moderate and High Temperature Service
ASTM A403 A403M Standard Specification for Wrought Austenitic Stainless Steel Piping Fittings
ASTM A420 A420M Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Low-Temperature Service
ASTM A860 A860M Standard Specification for Wrought High-Strength Low-Alloy Steel Butt-Welding Fittings
ASTM A733 Standard Specification for Welded and Seamless Carbon Steel and Austenitic Stainless Steel Pipe Nipples
DIN Standard MaterialDIN1629 Seamless Circular Unalloyed Steel Tubes Subject to special requirements
DIN 2440 Medium-weight threaded steel tubes
DIN 2441 Steel Tubes Heavy Weight For Suitable For Screwing
GOST Standard MaterialGOST-1050 Sized Bars Made of High-Quality Structural Carbon Steel With a Special Surface Finish
GOST 8732 Seamless hot-deformed steel pipes-Range of sizes
GOST 19281 Rolled Steel With Enhanced Strength
JIS Standard MaterialJIS G3452 Carbon steel pipes for ordinary piping
JIS G3454 Carbon steel pipes for pressure service
JIS G3455 Carbon steel pipes for high pressure service
JIS G3456 Carbon steel pipes for high temperature service
JIS G3457 Arc welded carbon steel pipes
JIS G3458 Alloy Steel Pipes
JIS G3459 Stainless steel pipes
JIS G3460 Steel pipes for low temperature service
BS EN Standard MaterialBS EN 10255 Non-alloy steel tubes suitable for welding and threading Technical delivery conditions
BS EN 10253-1 Butt-Welding Pipe Fittings  Part 1: Wrought Carbon Steel for General Use and Without Specific Inspection Requirements
BS EN 10253-2 Butt-welding pipe fittings. part 2: Non alloy ferritic alloy steels with specific inspection requirements
BS EN10253-3 Butt-welding pipe fittings Part 3: Wrought austenitic and austenitic-ferritic (duplex) stainless steels without specific inspection requirements
BS EN 10253-4 Butt-welding pipe fittings Part 4:Wrought austenitic and austenitic-ferritic (duplex)stainless steels with specific inspection requirements