BS 4504 standard flange facings types,welding ends of neck flange.

Weld Neck Flange – Welding Ends

 

All dimensions are in "mm" and All weights are in "kg" unless noted otherwise specified.
you may also check non standard sizes flange weight online calculation,flange surface area online calculation,flange surface volume online calculation from our flange calculator tool  and pipe fitting calculator.

The whole weight and dimension list of  flange directory Flange-dimension-and-weight

Flange Facings – BS 4504

————————————————————————————
BS 4504 flange facing types A to H are defined below. The dimensions vary with pipe size (DN) and pressure
rating (PN) as detailed in the following table.

BS 4504

BS 4504

 

BS 4504 Standard Flanges Dimensions and Tolerances

Dimension Range Tolerance
mm
Flange Facings Eccentricity of machined facing diameters < DN 100 1.0
> DN 100 2.0
a  (type B facing height) 2 mm +0, -1.0
3 mm +0, -2.0
4 mm +0, -3.0
5 mm +0, -4.0
6 mm +0, -5.0
b (type C and E facing height) All +0.5, -0
b (type G facing height) All +0, -0.5
b (type H facing height, outer) All +0.2, -0
c (type D and F facing height) All +0, -0.5
d (type H facing height, inner) All +0.5, -0
B and E (facing diameters) All +0, -0.5
C and D (facing diameters) All +0.5, -0
Surface Finish Facing types A, B, E and F All, turning Ra = 3.2 µm min 12.5 µm max
All, other than turning Ra = 3.2 µm min 6.3 µm max
Facing types C, D, G and H All Ra = 0.8 µm min 3.2 µm max
Flange Drilling Details B (diameter of bolt circle) Bolt sizes M10 to M24 ±0.9
Bolt sizes M27 to M45 ±1.4
Centre to centre of adjacent bolt holes Bolt sizes M10 to M24 ±0.45
Bolt sizes M27 to M45 ±0.7
All A (outside diameter) < DN 150 ±2.0
> DN 150 < DN 500 ±3.0
> DN 500 < DN 1200 ±5.0
> DN 1200 < DN 1800 ±7.0
> DN 1800 ±10.0
C (flange thickness, machined on both faces) < 18 mm thickness ±1.0
> 18 mm < 50 mm thickness ±1.0
> 50 mm thickness ±1.0
C (flange thickness, machined on front face) < 18 mm thickness +2.0, -1.0
> 18 mm < 50 mm thickness +4.0, -1.5
> 50 mm thickness +7.0, -2.0
Weld Neck Flanges, Code 111 B (outside diameter of hub at welding end) < DN 125 +3.0, -0
> DN 125 < DN 1200 +4.5, -0
> DN 1200 +6.0, -0
F (hub diameter) < DN 50 +0, -2.0
> DN 50 < DN 150 +0, -4.0
> DN 150 < DN 300 +0, -6.0
> DN 300 < DN 600 +0, -8.0
> DN 600 < DN 1200 +0, -10.0
D (length through hub) < DN 80 ±1.5
> DN 80 < DN 250 ±2.0
> DN 250 ±3.0
Slip on, Code 112 and Threaded,Code 113 E (slip on flange hub diameter)B (threaded flange hub diameter) < DN 50 +1.0, -0
> DN 50 < DN 150 +2.0, -0
> DN 150 < DN 300 +4.0, -.0
> DN 300 < DN 600 +8.0, -0
> DN 600 < DN 1200 +12.0, -0
> DN 1200 < DN 1800 +16.0, -0
> DN 1800 +20.0, -0
B (slip on bore diameter) < DN 100 +0.5, -0
> DN 100 < DN 400 +1.0, .0
> DN 400 < DN 600 +1.5, .0
> DN 600 +3.0, -0
D (length through hub) Same as Weld Neck D
Blank Flanges, Code 105 B (flange thickness) Same as C for all other flanges
C (unmachined centre portion) Maximum specified

BS 4504 Standard Flanges Type code,PN range and Marking Requirements.

Summary of flanges covered by BS 4504 : Section 3.1.

Code No. Description PN Range DN Range
101 Plate flange for welding(see page 8-65) PN 2.5 DN 10 to DN 2000
PN 6, 10, 16, 25, 40 DN 10 to DN 600
102 Loose plate flange with weld-on plate collar or for lapped pipe end (Weld-on plate collar = Code 1321 Lapped pipe end = Code 1331) PN 6, 10, 16, 25, 40 DN 10 to DN 600
104 Loose plate flange with weld-neck collar (Weldneck collar = Code 1341) PN 6, 10, 16, 25, 40 DN 10 to DN 600
PN 2.5, 6 DN 10 to DN 2000
105 Blank flange (see page 8-70) PN 10, 16 DN 10 to DN 1200
PN 25, 40 DN 10 to DN 600
PN 2.5, 6, 10, 16 DN 10 to DN 20002
111 Weld-neck flange (see page 8-66) PN 25 DN 10 to DN 1000
PN 40 DN 10 to DN 600
112 Hubbed slip-on flange for welding(see page 8-68) PN 6 DN 10 to DN 300
PN 10, 16, 25, 40 DN 10 to DN 600
113 Hubbed threaded flange (see page 8-69) PN 6, 10, 16, 25, 40 DN 10 to DN 150
121 Integral flange PN 6, 10, 16, 25 DN 10 to DN 2000
PN 40 DN 10 to DN 600

Note:

-Flanges > DN 2000, are not covered in this summary.

-Dimensions: Nominal sizes, DN followed by a numerical designation of size (a convenient round number for reference purposes), are used as defined in ISO 6708.

-Pressure Ratings: Nominal pressures, i.e. PN followed by a numerical designation of size (a convenient round number for reference purposes), are used as defined in ISO 7268.

1 Dimensions for these flanges are not covered in this summary.

2 The DN range for weld neck flanges extends to DN 4000 for PN 2.5, to DN 3600 for PN 6, and to DN 3000 for PN 10.

Designations/Marking

Marking. All flanges are marked with BS number, code number,PN,DN,material designation,manufacturers name or trade mark,cast number or melt identification,thread identification,An example follows:

BS 4504/111/B – PN 16 -DN 400 -B4 – XXX – 12345.

BS-4504-FLANGE-MARKING-REQUIREMENT

Cast Number or melt identification Manufacturer’s name or trade mark Material designation Nominal size, DN

Nominal Pressure, PN Flange face type (A – H) Flange code number British standard number

 

Our products like flanges are packaged to make sure that there’s no damage throughout transit. Just in case of exports, customary export packaging is completed in wooden boxes or cases. All flanges are marked with Trademark (Company’s LOGO), Grade, Size and Lot No. On requests we can do custom marking on our products.

TEST CERTIFICATES

Manufacturer Test Certificate as per EN 10204-3.1, EN 10204-3.2, Raw Materials Certificate, NABL approved Lab Test Report, 100% Radiography Test Report, Third Party Inspection Report etc.

● Production Capacity & Purchase Details
1. Supply Flange Dimension DN15 - DN2000 (1/2" - 120"), Forged Flange.
2. Material Carbon Steel: CT20, C22.8, RST37.2, S235JR, P235GH, P245GH, P250GH, ASTM A105 etc.
3. Material Stainless Steel: ASTM A182 F304 (1.4306), F304L(1.4307), F316(1.4404), F316L(1.4404), F321(1.4541) etc.
4. Flanges surface: Anti Rust Oil, Black Paint, Yellow Paint Coating, Hot Dipped Galvanized, Cold Galvanized ,FBE epoxy etc.
5. Quality Guarantee: EN10204 3.1 Certificate, NDE report.6.Stock below 24inch flange for all pressure class7.Provide ASME VIII design for 64in flange, 68in flange,72in flange,80in flange,88in flange,96in flange,100in flange,120in flange,etc

All   DIN  Flange dimension and weight list

 DIN FLANGE STANDARDS INTRODUCTION:
Description Rated Pressure / Presión Nominal / Nenndruck (in bar) (1 bar = 14.5 psi)
1 2.5 6 10 16 25 40 64 100 160 250 320 400
DIN
 Blind   Flanges 2527 2527 2527 2527 2527 2527 2527
 Flat flange for welding (slip-on) 2573 2576 2502 2503 2503
 Welding neck flanges 2630 2630 2631 2632 2633 2634 2635 2636 2637 2638 2628 2629 2627
 Lapped flanges, Plain collars 2641 2642
 Loose flanges and rings for welding 2652 2653 2655 2656
 Loose flanges and rings with neck for welding 2673
 Oval plain threaded flanges 2558
Oval flanges,with neck threaded 2561 2561
 Threaded flanges with neck 2565 2566 2566 2567 2567 2568 2569
 Long neck welding flanges 28115 28115
 Hubbed slip-on flanges for welding 86029 86030

All BS flange standard list

BS 4504 Standard Flanges Dimensions and Tolerances
BS 4504 Standard Flange Facings Types,Welding Ends of neck flange
BS 4504 Standard Flange Flange Facing Dimensions
BS 4504 Standard Flange Drilling Details and Dimensions.
BS 4504 Standard Code 101 Plate Flange and Dimensions
BS 4504 Standard Code 111 Weld Neck Flange and Dimensions
BS 4504 Standard Code 112 Slip On Flange and Dimensions
BS 4504 Standard Code 113 Threaded Flange
BS 4504 Standard Code 105 Blank Flange (Blind Flange)
BS 3293 Standard Welding Neck, Slip On Flange (150lb-600lb)
BS 10 Standard Table D, Table E, Table F, Table H Flange

All the flange standard list

ANSI/ASME FLANGE STANDARD EN FLANGE STANDARD BS FLANGE STANDARD
DIN FLANGE STANDARD JIS FLANGE STANDARD UNI FLANGE STANDARD
API 6A/6B/6BX FLANGE STANDARD AWWA FLANGE STANDARD KS FLANGE STANDARD
GOST/ГОСТ FLANGE STANDARD ISO FLANGE STANDARD AS FLANGE STANDARD
SANS/SABS FLANGE STANDARD LONG WELD NECK FLANGE ASME VIII FLANGE