en-10253-1-type-2d-elbow

All dimensions are in "mm" unless noted otherwise specified.
All weights are in "kg".

you may also check non standard sizes pipe fitting weight online calculation, pipe fitting surface area online calculation,pipe fitting surface volume online calculation from our pipeline tool link:

https://alloypipefitting.com/fitting-calculator.html

The whole weight and dimension list of pipe fitting directory

https://alloypipefitting.com/fitting-dimension-and-weight.html

Download the PDF fileEN-10253-1-butt-weld-fittings-2007

EN 10253-1 BUTT WELDING PIPE FITTINGS
ELBOW 2DELBOW 3DELBOW 5DREDUCER FORM 1REDUCER FORM 2
EQUAL TEESREDUCING TEESDISHED ENDSCAPSTolerance

1. Technical drawings of 90°, 45° & 180° elbows of type 2D

2D ELBOW

180° elbows are also called return bends. For type 2D, the center-to-end radius R is approximately equal to 1*D.

2. Dimensions of 90°, 45° & 180° elbows of type 2

DNDTFCB
2026.92.3255039
2533.72.6255042
3242.42.6326453
4048.32.6387662
5060.32.95110281
6576.12.963127102
8088.93.276152121
100114.33.6102203159
125139.74.0127254197
150168.34.5152305237
200219.16.3203406313
250273.06.3254508391
300323.97.1305610467
350355.68.0356711533
400406.48.0406813610

*D: Outside diameter of elbows or return bends. H: Face to center distance for 45° elbows.

*F: Center-to-end radius of the elbow. B: Face to top length for return bends.

*C: Center-to-center length of the return bend. T: Wall thickness.

 *All dimensions are in mm unless otherwise specified.

1. Tolerances on dimension according to EN 10253-1

1) All diameters of EN 10253-1 pipe fittings shall be measured at the welding ends of the fittings. The tolerance is ±1% or ±0.5 mm whichever is the greater.

2) In order to ensure the flow-way area through the fitting is not excessively reduced, the internal diameter(not applicable to dished ends and caps) shall be greater than 80% of the theoretical internal diameter(ID), as calculated by: ID = OD - 2T.

3) Tolerances for ovality are:

at the welding ends: 2%;

on the body for elbows and return bends: 4%.

The ovality(Ov) shall be calculated by:

Ov = 200 * (Dmax - Dmin) / (Dmax + Dmin) in %.

Dmax: maximum measured diameter in one section.

Dmin: minimum measured diameter in one section.

4) Wall thickness tolerances

DTTolerance
mmmmminusplus
≤406.4≤4
>4
-12.50%0.35

 *D: Outside diameter at the welding end. T: Wall thickness.

 *The minus tolerance also applies to the body of the fitting.

5) Tolerances on specific dimensions

DF-G-HBCKL
≤114.3±2±7±7±4±2
114.3<D≤219.1±2±7±7±7±3
219.1<D≤406.4±3±7±10±7±5

 *D: outside diameter;

 *F: distance from the axis of the center line to the face of the branch outlet of equal tee.

 *G: distance from the axis of the center line to the face of the branch outlet of reducing tee.

 *H: Face to center-line distance for 45°.

 *B: Face to top distance for 180° return bends.

 *C: Center to center distance for 180° return bends.

 *K: height of dished ends or caps.

 *L: Face to face length of reducers(both concentric & eccentric).

6) Tolerances on the form of fittings

The tolerance on the form of each type of fitting Q = 1% of the outside diameter(D) or 1 mm, whichever is greater. See the figure illustrated below.

2. End finish of EN 10253-1 butt welding pipe fittings

According to DIN EN 10253-1,
for wall thickness T < 3.0 mm, the ends may be plain or slightly chamfered.
for wall thickness T ≥ 3.0 mm, the ends shall be bevelled with an angle of 30 degrees to 35 degrees with a face of 1.6 mm ± 0.8 mm.
The welding ends of EN 10253-1 pipe fittings shall be free from harmful blurs.
Specially, the ends of dished ends with diameter ≥ 159 mm shall be bevelled with an angle of  30 degrees to 35 degrees with a face of 1.6 mm ± 0.8 mm.